Author Topic: Blades....  (Read 3963 times)

Offline dgman

  • *****
  • Hero Member
  • Posts: 6916
    • View Profile
Re: Blades....
« Reply #15 on: March 24, 2011, 10:21:45 pm »
It's never to late Bill! Just adds to the confusion! :D
Dan In Southern California

Bill P

  • Guest
Re: Blades....
« Reply #16 on: March 24, 2011, 10:35:22 pm »
Then my job here is done.   ;D

Bill

chief

  • Guest
Re: Blades....
« Reply #17 on: March 24, 2011, 11:53:02 pm »
I buy my blades at Home Depot and sometimes you can get 2 for 1 in a package.  They are 10" carbide tipped.  They are not as good as the Diablo blades, but 2 for 1 make it up.  Use a zero clearance insert and make sure your fence is parallel to the blade and the miter is square.  When I start a new project that will require a lot of table saw cuts I triple check my TS alignments and make sure everything is perfect.  1/64" will add up after numerous cuts.  The time spent calibrating your saw will be worth it in the long run.  I havent sharpened a blade in years.  A blade will appear dull a lot of times when it is really just dirty with pitch build up.
The easy way to clean a blade is get the lid from a 5 gallon plastic bucket and pour in some cleaner.  You can use water and baking soda, 1qt water 1C baking soda and soak the blade for 2 hours and then clean it up with a brass bristle brush.  Dry the blade thouroughly and spray with DW-40 and then wipe clean to prevent rust.  I use a cleaner called Lestoil you can get at Ace and it works after just a few minutes of soaking.  You can reuse the Lestoil so it will last a long time for the $7 investment.

Offline BilltheDiver

  • *****
  • Hero Member
  • Posts: 1475
    • View Profile
Re: Blades....
« Reply #18 on: March 25, 2011, 01:20:28 pm »
A little off the subject GB, but it might be an idea for you.  You mentioned the baseball team.  I used to know a guy who made a deal with the local team/stadium and got all the broken bats for free.  He would rip the bats in half on his tablesaw, install cup pegs on them and sell them as coat racks.  He also sold wooden racks to hold a baseball and a bat through the stadium.  The only tools in his shop were a tablesaw, a drill press, and a stationary belt sander but he stayed pretty busy in retirement.  Maybe you could work something out there.
"Measure twice, cut once, count fingers"

Offline GrayBeard

  • *****
  • Hero Member
  • Posts: 7088
  • My DW 788 sends you HUGZZZZ from Missouri, USA!
    • View Profile
Re: Blades....
« Reply #19 on: March 25, 2011, 02:17:20 pm »
Great Ideas...will be meeting with team rep next week and feel them out!

Thanks

~~~GB~~~
I never really wanted to grow up....All I wanted was to be able to reach the cookie jar...and play with my DW 788

Offline dgman

  • *****
  • Hero Member
  • Posts: 6916
    • View Profile
Re: Blades....
« Reply #20 on: March 25, 2011, 08:56:52 pm »
Great Ideas...will be meeting with team rep next week and feel them out!

Thanks

~~~GB~~~
I hope it's a woman! ::)
Dan In Southern California

Bill P

  • Guest
Re: Blades....
« Reply #21 on: March 25, 2011, 08:59:26 pm »
And that's why Dan is a hero member!   :D

Bill

Offline GrayBeard

  • *****
  • Hero Member
  • Posts: 7088
  • My DW 788 sends you HUGZZZZ from Missouri, USA!
    • View Profile
Re: Blades....
« Reply #22 on: March 25, 2011, 09:06:27 pm »
She is ALL woman and a real looker...Lindsey is also a former all star college softball player with 'great hands'!

~~~GB~~~
I never really wanted to grow up....All I wanted was to be able to reach the cookie jar...and play with my DW 788

Offline Rapid Roger

  • *****
  • Hero Member
  • Posts: 1468
  • Hutchinson, Kansas
    • View Profile
Re: Blades....
« Reply #23 on: March 25, 2011, 10:10:18 pm »
Hey chief,
I clean my table saw blades with Windex, an old tooth brush and paper towels. I wipe them down with a light machine oil on a paper towel to prevent rust. It takes me about ten minutes to clean the pitch off of a 60t blade and she's ready to go!

Rog
An ounce of responsablity is worth 10 pounds of state and fedral laws.

SD Scroller

  • Guest
Re: Blades....
« Reply #24 on: March 30, 2011, 02:37:38 am »
Personally i use whatever blade is on the table saw. 

Offline newtoscroll

  • *
  • Newbie
  • Posts: 41
    • View Profile
Re: Blades....
« Reply #25 on: March 30, 2011, 08:21:21 am »
thanks for the idea of cleaning the blades for the table saw.  When cutting common pine it is not hard on the saw but with hard woods especially ebony, the blade can take a toll. 

Offline tinker1

  • **
  • Jr. Member
  • Posts: 96
    • View Profile
Re: Blades....
« Reply #26 on: January 13, 2012, 08:27:00 am »
Information when deciding which blade to use:
http://www.woodcraft.com/Articles/Articles.aspx?articleid=691

Tink

Offline Jim Finn

  • *****
  • Hero Member
  • Posts: 507
    • View Profile
Re: Blades....
« Reply #27 on: January 13, 2012, 09:59:48 pm »
The only cut I ever make on my table saw is rip cut... so I have a 40 tooth ripping blade.  I do all my crosscuts on my 12" sliding miter saw and re-saw with my band saw.
20"Hegner Polymax-3 (2008)
25"Hegner Multimax-3 (1986)

No PHD, just a  DD 214

joey65746

  • Guest
Re: Blades....
« Reply #28 on: January 14, 2012, 04:37:11 am »
Freud the hole way in my shop they are awsome  they are thin kerf  there is realy not one blade that can do it all but most of yhr time i have a 80 or more tooth 

Offline BilltheDiver

  • *****
  • Hero Member
  • Posts: 1475
    • View Profile
Re: Blades....
« Reply #29 on: January 14, 2012, 09:24:42 am »
I use a 60 in the table saw and a 80 in the Radial arm and get them both professionally sharpened whenever they don't feel new.  $10 to sharpen a 10" carbide blade is a great investment in my book.
"Measure twice, cut once, count fingers"

 

SMF

Teknoromi