« previous next »
Pages: 1 [2]   Go Down

Author Topic: Christmas Bell  (Read 5378 times)

Offline Merlin

  • *****
  • Hero Member
  • Posts: 1191
    • View Profile
Re: Christmas Bell
« Reply #15 on: October 13, 2012, 04:40:40 pm »
May I cut in here and ask.... How large is that ornament cut.
I d/loaded the pattern and it prints at 8x81/2 inches with approx: 51 internal cuts ... many very small.
I wood hate to cut it any smaller ::)

***Merlin***
Logged
Try not! Do,
or do not
There is no try

Yoda "Empire Strikes Back" 1980

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Christmas Bell
« Reply #16 on: October 13, 2012, 05:18:02 pm »
Merlin, I was brave and reduced the size to 5 1/2 inches just to see if I could do it. another one I reduced from 11inches to 4 1/2 inches was my angels with doves by Sue Mey picture attatched.
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline Tomsunnu

  • *****
  • Hero Member
  • Posts: 1609
    • View Profile
Re: Christmas Bell
« Reply #17 on: October 13, 2012, 10:01:30 pm »
Keith,beautifully cut :)
Mahendra
Logged
mahendra

smitty0312

  • Guest
Re: Christmas Bell
« Reply #18 on: October 14, 2012, 09:09:53 am »
I love that pattern, it came out very nice!!
Logged

Offline Reaper

  • ****
  • Sr. Member
  • Posts: 475
    • View Profile
Re: Christmas Bell
« Reply #19 on: October 14, 2012, 11:11:59 pm »
The bell and the angels are nice.Great cutting....
Logged

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: Christmas Bell
« Reply #20 on: October 15, 2012, 07:13:05 am »
Great  bell Keefie, I have that pattern in my extensive Christmas file, I may get to cut it one day.

Marg
Logged
MARG

No one notices what I do until I'm not here to do it............

Offline Danny

  • *****
  • Hero Member
  • Posts: 1674
    • View Profile
Re: Christmas Bell
« Reply #21 on: October 15, 2012, 01:07:07 pm »
I cut my Bells full size.  Was using 1 hour as a reference for pricing.  Think it did take me a few hours.  No more tho.  Using a FD-UR#1 blade (to me) is like following the line with a pencil.  Danny  :+}
Logged
Danny  :+}

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Christmas Bell
« Reply #22 on: October 15, 2012, 01:31:51 pm »
Danny, I use the FD UR #1  for 99% of all my work, as you say it's like following the line with a pencil. ( but the bells are much more fiddley to cut with the size reduced lol)
« Last Edit: October 16, 2012, 03:45:47 am by Keefie »
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

jlatorre

  • Guest
Re: Christmas Bell
« Reply #23 on: October 15, 2012, 07:37:58 pm »
very nice work, thanks for sharing
Logged

Offline troy_curtis

  • *****
  • Hero Member
  • Posts: 1104
  • No matter where you go...there you are.
    • View Profile
Re: Christmas Bell
« Reply #24 on: October 19, 2012, 12:59:58 am »
I cant believe I didnt post on this yet. It is a beautiful design....very nice work. Love the red in the back. Thanks for sharing.
Logged

Offline Marcellarius

  • *****
  • Hero Member
  • Posts: 6135
  • Scrolling each day, keeps the doctor away
    • View Profile
    • Some of my work
Re: Christmas Bell
« Reply #25 on: October 19, 2012, 08:34:28 am »
better late then never...

Great Chirstmas bell. really good job
Logged
Marcel

sometimes I make designer firewood....
Pages: 1 [2]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj