1
General Scroll Saw Talk / Scroll Saw Village
« on: February 20, 2022, 09:49:21 am »
Is the site down or is it just me?
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Scroll Saw Talk / Camera recomendation
« on: October 27, 2014, 12:59:34 pm »
I am hoping someone could recomend a camera that will take a good picture of a scroll saw project.
i have a cheap camera which just doesn't do the job. Looking for some recomendations on a not to
costly camera. Thanks for your help. Al
i have a cheap camera which just doesn't do the job. Looking for some recomendations on a not to
costly camera. Thanks for your help. Al
4
General Scroll Saw Talk / Saw Trouble
« on: June 29, 2014, 05:58:21 pm »
Delta 16 inch varible speed saw.
Today I was lubing the saw - Removed upper and lower pivot pins
per the manual. Both came out normallyand the bottom one went
back in fine but the upper one will not tighten. I have run a tap into
the hole in the casting (8mm/125) still no luck. (yes that is the size)
A screw of that size tighens just fine in the casting. Pivot pin threads
look OK and a nut tightens on it fine.
Any thoughts ?
Is it time to look for a new saw? AL
Today I was lubing the saw - Removed upper and lower pivot pins
per the manual. Both came out normallyand the bottom one went
back in fine but the upper one will not tighten. I have run a tap into
the hole in the casting (8mm/125) still no luck. (yes that is the size)
A screw of that size tighens just fine in the casting. Pivot pin threads
look OK and a nut tightens on it fine.
Any thoughts ?
Is it time to look for a new saw? AL
5
General Scroll Saw Talk / Blade Selection
« on: June 14, 2014, 10:52:59 am »
What blade works best for you in 3/4 inch soft pine ? I have been having a rough time trying to cut it.
Blade speed also and thanks for your advise. Al
Blade speed also and thanks for your advise. Al
6
The Coffee Shop / Concert in Holland
« on: January 10, 2014, 05:26:04 pm »
Concert is to honor the war dead in freeing Holland in WW2.
This 13 year old can play. Worth listening.
http://www.flixxy.com/trumpet-solo-melissa-venema.htm
This 13 year old can play. Worth listening.
http://www.flixxy.com/trumpet-solo-melissa-venema.htm
7
General Scroll Saw Talk / Saw acting up
« on: December 16, 2013, 08:33:38 pm »
Delta Shopmaster SS250 bought 5 weeks ago new in the box off Craigs list.
Saw just started this today. Speeds up slows down then quit. Started back up but would not run slow only fairly fast and quit again. I losened the on & off switch and blew in it and reattached it and the saw runs again at the higher speed. Any ideas on what is going on with it? I haven't tried changing the speed yet. You help is appreciated.
Saw just started this today. Speeds up slows down then quit. Started back up but would not run slow only fairly fast and quit again. I losened the on & off switch and blew in it and reattached it and the saw runs again at the higher speed. Any ideas on what is going on with it? I haven't tried changing the speed yet. You help is appreciated.
9
General Scroll Saw Talk / Wood Question
« on: October 24, 2013, 05:42:16 pm »
Anyone know anthing about "Kiwi Pine'. I got 1X6 orf it out of the select stock at Menards. Seems very hard to cut. Blade Choice?
Pages: [1]
