76
Introduce Yourself. / Re: Howdy
« on: November 08, 2019, 02:11:19 pm »
Hello from North Dakota 
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
77
Introduce Yourself. / Re: New (again) from Beautiful Southern Oregon
« on: October 18, 2019, 07:18:34 pm » Welcome back. thought you were familiar 78
Introduce Yourself. / Re: New... sort of
« on: October 13, 2019, 06:19:47 pm » You must be up and running and logged in. Good to meet you. I am Judy from North Dakota. I used to do the Renaissance in Arizona. I sure miss it this time of year.
79
Brag Forum / Re: Been a while since I last Bragged.... Blush!
« on: October 09, 2019, 11:08:28 am » Definitely worth bragging about. Woner what one of North Dakota would look like 
80
Ask Steve a question. / Re: Jet JWSS-22 Scroll Saw Clamp Jig
« on: September 28, 2019, 07:18:58 pm »
A LETTER? As in a paper in an envelope??? I am willing to try anything. Is his mailing address available somewhere?
I am willing to try anything. Is his mailing address available somewhere?
81
Ask Steve a question. / Re: Jet JWSS-22 Scroll Saw Clamp Jig
« on: September 28, 2019, 01:17:37 pm »
Guess we will just have to keep trying. If you hear from him please let me know.
82
General Scroll Saw Talk / Re: Scroll saw blade storage
« on: August 07, 2019, 02:08:01 pm »
A picture is worth a couple of words 
Cut 1/2 inside diameter PVC to 5 inch lengths. Cut one 4 inches.
cut scrap plastic into 3/4 inch pieces (I used old VCR tape cases)
super glue onto the end of the pipe. make sure it sits long enough to cure.
With file or belt sander sand off excess plastic so it leaves the pipe smooth all around.
cut base shape from scrape 1 inch board (really it is only3/4 in)
Let me know if you want my pattern but it depends on how many blade holders you want.
drill 5/8th holes 1 inch by 1-1/2 apart with spade bit so just the point comes out leaving a thin "floor".
The covers are the pipe caps.
The four inch front pipe holds the blade in current use.
blades usually come with labels that I just tape on.
Hope this helps feel free to ask any questions if I didn't make something quite clear. Hope this works for you. Sizes can be adjusted. Bigger pipe, bigger holes etc.
Cut 1/2 inside diameter PVC to 5 inch lengths. Cut one 4 inches.
cut scrap plastic into 3/4 inch pieces (I used old VCR tape cases)
super glue onto the end of the pipe. make sure it sits long enough to cure.
With file or belt sander sand off excess plastic so it leaves the pipe smooth all around.
cut base shape from scrape 1 inch board (really it is only3/4 in)
Let me know if you want my pattern but it depends on how many blade holders you want.
drill 5/8th holes 1 inch by 1-1/2 apart with spade bit so just the point comes out leaving a thin "floor".
The covers are the pipe caps.
The four inch front pipe holds the blade in current use.
blades usually come with labels that I just tape on.
Hope this helps feel free to ask any questions if I didn't make something quite clear. Hope this works for you. Sizes can be adjusted. Bigger pipe, bigger holes etc.
83
General Scroll Saw Talk / Re: Scroll saw blade storage
« on: August 06, 2019, 04:52:17 pm »
I make my own with PVC pipe. if you want more info just let me know
85
Pattern Requests. / Re: searching for this
« on: July 20, 2019, 05:41:21 pm »
It is an established fact that I am a "little off" 
Thanks for giving it a shot.
Thanks for giving it a shot.
86
Pattern Requests. / searching for this
« on: July 19, 2019, 12:57:39 pm »
Does anyone know where I can get this pattern? 
87
Introduce Yourself. / Re: Hi new guy here
« on: June 30, 2019, 12:16:54 pm »
;Hello there. And welcome to the forum. It isn't near as busy it used to be but we are all "lurkers" so post anytime with your work or questions. We are all here to help, admire, and suggest.
I am familiar with where you are. I did the Renaissance there for 20 years. Retired to just scroll sawing now.
I am familiar with where you are. I did the Renaissance there for 20 years. Retired to just scroll sawing now.
88
General Scroll Saw Talk / Re: listening to music
« on: June 28, 2019, 11:57:12 am »
I am sorry you don't hear well.
I would suggest you get a good set of head phones attach them to your music source and turn the volume up. You may not "hear" the music, but maybe you could "feel" it.
I would suggest you get a good set of head phones attach them to your music source and turn the volume up. You may not "hear" the music, but maybe you could "feel" it.
89
Introduce Yourself. / Re: Hello Everyone
« on: June 04, 2019, 09:51:18 am »
Hi and Welcome. I am Judy from North Dakota
I am Judy from North Dakota
90
General Scroll Saw Talk / Re: listening to music
« on: May 20, 2019, 07:26:32 pm »
I use a noise canceling blue tooth headset and listen to books from audible.
