16
General Scroll Saw Talk / Re: Pattern removal cost
« on: July 24, 2018, 03:18:49 pm »
I use spray adhesive and mineral spirits. The only time I use tape is when I stack cut
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
Introduce Yourself. / Re: Newbie
« on: July 16, 2018, 07:09:20 am »
Welcome Brian. Lots of helpful people on this site.
18
Brag Forum / Re: Proud to be
« on: June 30, 2018, 06:57:47 pm »
I feel the same way as Norm. I wish politicians could get along as well as us scroll saw folks
19
Introduce Yourself. / Re: Hi from Illinois
« on: June 21, 2018, 12:26:20 am »
Welcome Rusty, You will find lots of friendly advice here and almost always your questions will be answered.
20
Introduce Yourself. / Re: Welcome
« on: June 19, 2018, 06:25:05 pm »
Im Brent from Canada. Welcome to the hobby and the forum
21
General Scroll Saw Talk / Re: Strange dewalt happening
« on: June 19, 2018, 06:12:39 pm »
Thanks for the info. I just wanted to know if i would damage the saw using it this way. I dont miss using my block of wood
22
General Scroll Saw Talk / Strange dewalt happening
« on: June 18, 2018, 08:18:04 pm »
My dw788 is about 3 months old i had to tighten my lamp and realized the bottom bolt is stripped so i tightened the top extra tight an now my head stays up without my piece of wood i loosened the lamp bolt and it still does it i have been using the saw but am wondering if there is a problem when i lft it it locks into place and there is very little resistance to put it back down right now it works like the delta.
23
Introduce Yourself. / Re: Hello from South Carolina
« on: June 05, 2018, 06:04:22 pm »
Welcome. Im Brent from orangeville ontario canada
24
Introduce Yourself. / Re: Hello From D-Tone
« on: June 05, 2018, 06:01:51 pm »
Welcome to the forum D tone . And welcome to a very addictive hobby.
25
General Scroll Saw Talk / Re: Foot switch
« on: May 31, 2018, 09:30:13 pm »
I bought a deadman swtith and used it once. I do all my work standing and it was too uncomfortable. I can see the advantage if sitting but that is not an option for me due to lmited shop space. A one care garage doesnt cut it. Time for a bigger house
26
General Scroll Saw Talk / Fret work clean up
« on: May 31, 2018, 09:25:27 pm »
Not sure how many scrollers do this, but i keep a dull 2/0 blade and use it by hand to clean all my fret work fuzzies. I find it faster then using blade sanders and small pieces of sand paper. I also use the end of a 5 blade to clean glue sqeeze out
27
General Scroll Saw Talk / Re: Better bulb for dewalt
« on: May 31, 2018, 09:17:28 pm »
I cant find any led bulbs that fit this lamp i hate the orange glow it gives off. I found a 40 watt, but its way to hot as i am in the habit of moving my light while cutting. Made that mistake once and put the old one back in
28
General Scroll Saw Talk / Re: Need help on a scroll saw purchase.
« on: May 23, 2018, 06:34:24 pm »
I have a dewalt and your saw is my back up I use from 2/0 up to 9 and it works fine I prefer to use it when cutting thicker stock cause it cuts faster then the dewalt.
29
General Scroll Saw Talk / Re: Saw upgrade
« on: May 13, 2018, 08:47:08 pm »
I wish we could find these deals in Canada
30
Pattern Requests. / Step aside coffee
« on: May 03, 2018, 06:19:31 am »
I made the step aside coffee this is a job for alcohol pattern for my neighbor. My wife saw it and asked if there was one with a wine bottle.
