Scrollsaw Workshop Community -Please register to enable posting.

General Category => Brag Forum => Topic started by: wntrrwd on February 18, 2012, 01:12:55 am

Title: First box
Post by: wntrrwd on February 18, 2012, 01:12:55 am

OK...Nothing great about this but thought I would share it any way. This is the first box I ever did. I still need to sand it and put some type of coating on it but all in all I don't think it is to bad for a newbie.

Title: Re: First box
Post by: Dawie on February 18, 2012, 01:15:39 am

Looks great! Thanks for sharing.
David

Title: Re: First box
Post by: DWSudekum on February 18, 2012, 01:23:56 am

You did very good on that heart box.  Thanks for sharing it with us.


DW

Title: Re: First box
Post by: wntrrwd on February 18, 2012, 01:27:55 am

What is the best way to sand it on the inside so it is more even? Probably should have thought of that before I put it together...lol!

Title: Re: First box
Post by: wombatie on February 18, 2012, 01:31:15 am

Thats great you certainly put your heart into it.  ::)  Sorry

Marg

Title: Re: First box
Post by: Russ C on February 18, 2012, 05:52:26 am

Looks great, nick work.  :)  You might try looking for some spindle type sanders that fit in your drill press.

Title: Re: First box
Post by: Tomsunnu on February 18, 2012, 06:41:55 am

Great start! Very nicely cut , Newbie- I don't think so :D

Title: Re: First box
Post by: Al W on February 18, 2012, 08:32:19 am

Nice job.  Looks like a fine start to a long hobby.

Title: Re: First box
Post by: daliclimbs on February 18, 2012, 08:56:01 am

Nice job came out great.

Title: Re: First box
Post by: Keefie on February 18, 2012, 01:10:30 pm

very nice work, especially as it's your first box. thanks for sharing.

Title: Re: First box
Post by: malc on February 18, 2012, 03:28:04 pm

If my first cut had been thet good I would have been very pleased, well done :)
Malc

Title: Re: First box
Post by: newfie on February 18, 2012, 04:37:12 pm

nice work thanks for sharing

Title: Re: First box
Post by: SheGold on February 19, 2012, 04:28:53 am

Nice job... Glad you shared... Sheila

Title: Re: First box
Post by: Marcellarius on February 28, 2012, 11:06:18 am

looks nice, would like to see the finished version to!

Title: Re: First box
Post by: boxmaker on February 28, 2012, 03:35:21 pm

It came out nice, I would try a spindle sander, just keep checking while sanding, so you don't take too much off and make your lid keeper too loose.

Title: Re: First box
Post by: TheMelster on February 28, 2012, 03:43:26 pm

 :) :) :) Don't recall where I saw it, youtube or here,,,, a power drill with sanding bit was mounted in a vice, then you manuver the part around the drum bit...looked easy enough. Hey this might be a good place to use the dremel if the area to be sanded is not too far down/deep that is for the sanding bit.

Title: Re: First box
Post by: frankorona on February 29, 2012, 09:03:40 am

Nicejob, looks great