Scrollsaw Workshop Community -Please register to enable posting.

General Category => Brag Forum => Topic started by: Mainewoods on January 11, 2011, 07:54:07 am

Title: For Mom's Bday
Post by: Mainewoods on January 11, 2011, 07:54:07 am

Just finished cutting this.  It's the free pattern I downloaded from Berrybasket <---Thank You!!!!

1/4" Baltic Birch cut with #7 Scroll Reverse.  The pattern is very accurate in that all the slot joints are nice and tight.  Going to do a lemon oil and laquer finish. 

Comments welcomed!

Title: Re: For Mom's Bday
Post by: tux_linux on January 11, 2011, 08:25:14 am

 :o really beautiful. She'll like it!

regards
Torsten

Title: Re: For Mom's Bday
Post by: Chachi on January 11, 2011, 08:59:12 am

Great work I'm sure she will love it for sure what MoM wouldn't.

Title: Re: For Mom's Bday
Post by: scrollgirl on January 11, 2011, 09:04:47 am

That is really sweet!  She is going to LOVE it!!! :D

Sheila

Title: Re: For Mom's Bday
Post by: Marcellarius on January 11, 2011, 09:12:57 am

that's really nice. great job.

Title: Re: For Mom's Bday
Post by: julief on January 11, 2011, 09:15:17 am

Very nice.

Title: Re: For Mom's Bday
Post by: Russ C on January 11, 2011, 09:59:25 am

Awesome job, it is beautiful. Thanks for sharing with us.  :)

Title: Re: For Mom's Bday
Post by: marmoh on January 11, 2011, 10:43:37 am

Very nice job.  I know she will love it.

Title: Re: For Mom's Bday
Post by: heiko rettberg on January 11, 2011, 10:50:49 am

Looks cool, good job.

Title: Re: For Mom's Bday
Post by: Marshall on January 11, 2011, 11:09:58 am

Impressive cutting job .......she should love it ........

Title: Re: For Mom's Bday
Post by: Dawie on January 11, 2011, 11:51:22 am

Great job you did there.
David

Title: Re: For Mom's Bday
Post by: Judy Hunter on January 11, 2011, 12:00:57 pm

Very Very Nice!!!

Title: Re: For Mom's Bday
Post by: Intarsia92 on January 11, 2011, 02:33:03 pm

Super job, looks Good!

Title: Re: For Mom's Bday
Post by: GrayBeard on January 11, 2011, 03:38:25 pm

Mom can be very proud of her 'boy'!

Nice Work!

~~~GB~~~

Title: Re: For Mom's Bday
Post by: Mainewoods on January 12, 2011, 07:07:20 am

Thanks everyone!!!  I was a little apprehensive about attempting this due to the tab and slot assembly.  I was concerned I wouldn't get the joints tight enough and the whole thing would be sloppy.  In my caution, I made a couple slots a smidge too tight, but was able to sand them out a little and now everything fits nice and snug!

Thanks again Berry Basket, great pattern! :)

Title: Re: For Mom's Bday
Post by: Tim2beupinAz on January 12, 2011, 01:08:25 pm

Very nice looking. Great Job there.

Title: Re: For Mom's Bday
Post by: bampasr on January 12, 2011, 02:02:55 pm

Just saw you work you did a great job.

Title: Re: For Mom's Bday
Post by: dgman on January 12, 2011, 10:55:12 pm

Hey Mainewoods, Thats the way to do it! If I have a tab and slot to cut I aways cut the tab just a little tight, then sand to fit!

Title: Re: For Mom's Bday
Post by: boxmaker on January 13, 2011, 07:55:56 pm

That is really nice Mainewoods, and thanks for the tip, I made a project with tabs awhile back and some of the tabs were too loose.

                                                                             Mark