Scrollsaw Workshop Community -Please register to enable posting.
General Category => General Scroll Saw Talk => Topic started by: boxmaker on September 16, 2010, 11:55:49 pm
-
I recently seen a video somewhere on the internet, sorry can't remember where, but the guy used electrical tape for putting the pieces together for a stack cut. Anyone heard of this?. I think it might be easier to remove then packing tape.
Mark
-
Not sure I use Packaging tape with no problems. I have also used blue painters tape.
Dan
-
I always say do what works for you. Give it a try and report back!
-
Wrap 'em in blue or green painters tape (delicate), spray on the glue and apply the pattern, and sometimes top it with clear packing tape. Works well with stacks up to 6 or more layers.
Some use bits of thin double-sided tape applied in the external waste area. Some used brads in the waste area. Some apply tape only to the edges of the stack. You could use anything that rings your bell, but sort of remember that you need to get it off the finished piece both top and bottom and have the piece take a finish. That can be a challenge with the thin and delicate stuff, or maybe the top one id just sacrificial. You just have to get the glue residue and tape off, so if it works for you, it works.
Terry
-
some use a heat gun to remove or unlosen the tape, pattern, glue etc., i use a hair dryer and it seems to work for me. :)
-
I am not sure how that would work and I don't think it would be cost effective. 8)
-
Since electric tape is rubberizes - it may not allow your piece to slide easily. Also, The glue in electrical tape tends to be a little gooey. I use blue painters tape for two reasons. The first is, it is made to come off easily and the second is, I can see it. I have really bad eyes and the packing tape is hard to see on tiny areas unless you see the sheen.
-
Well I tried the electrical tape tonight, and I do not like it, Julie is right it doesn't slide very well and rubs off while you are turning. I like the painters tape idea, I have been using packaging tape and it seems to take me forever to get it off, especially on delicate pieces. Thanks for the info.
Mark
-
Mark,
for the packaging tape just wipe on, or spray on mineral spirits and let it soak in for a few minutes it will release the glue. I have a spray bottle full of odorless M/S in my shop all the time for just such an application.
-
Dunk, It never occured to me to put the spirits in a spray bottle. I am going to do that today. I have always dabbed it on.
-
I do like using my packaging tape, I believe it does help lubricate the blade when cutting. I have used the mineral spirits for removing the glue from the wood, but never figured it would absorb through the plastic tape to help remove the tape. I also like the idea of a spray bottle, Thanks Dunk.
Mark
-
I apply the packing tape to the pattern If I'm using hardwoods that my burn only, like Cherry, Maple and oak. I will not use it on pine, walnut, mahogany or poplar as these woods do not burn for me when cutting. After the pattern is applied, I will apply the tape. After cutting I use a heat gun to loosen the pattern. The tape come off easily with the pattern Then with a soft rag apply mineral spirits to remove the glue residue.
-
You may find that the ms does not totally remove the packing tape and it may take a 2nd application. I still find it less messy than other methods.
-
I like to use spraying thinner rather than mineral spirits. It works better for me, not as much oily residue. You can put it in a spray bottle to. 8)
-
I use masking tape and it seems to come off a little cleaner then packing tape. I originally tried it because I was out of packing tape and didn't want to go to the store.
I also used electrical tape a couple of times when it was handy. The only advantage I saw was that the stretchy nature of electrical tape gave me a tight stack of pieces that were not the same size and shape. But the high price of good quality electrical tape makes it un-practical for most applications, for me anyway.
MrsN
-
Blue tape wrapped all the way around the stack works for me
-
I like to use spraying thinner rather than mineral spirits.
I'm not quite sure what spraying thinner is but if it is paint thinner.
If you look on the can/bottle of "paint thinner" you will probably see in small print it is in fact mineral spirits. That is what paint thinner is. If you are using lacquer thinner or something else then of course that is a different story.
-
Dunk is right! Paint thinner is mineral spirits!
-
Wow learned somethin again today. Paint thinner=mineral oil.
David
-
not mineral oil - mineral spirits