Scrollsaw Workshop Community -Please register to enable posting.

General Category => Brag Forum => Topic started by: tommyb43 on February 09, 2015, 05:07:24 pm

Title: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: tommyb43 on February 09, 2015, 05:07:24 pm

Hi All

This is another attempt an one of Steve's Word Art, Number 5 cutting on new hobby list  ;D I must be getting better not to many crooked lines on this one, And I stacked this just to see what all the fuss was about AND IT WORKED Well chuffed with my self.
2 X 9 mm Birch Plywood and a no 2 Spiral Blade.

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: gordster on February 09, 2015, 07:06:21 pm

Good job Tommy..word art is always popular

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: pierre62 on February 09, 2015, 07:11:00 pm

Nice job Tommy.

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: DWSudekum on February 09, 2015, 07:52:00 pm

Nicely done Tommy.  Thanks for sharing this with us.


DW

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: Rover2 on February 09, 2015, 08:55:34 pm

Nice cutting job Tommy.  Thanks for sharing with us.

Al

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: frankorona on February 10, 2015, 09:17:54 am

Great work, thanks for sharing.

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: rdatelle on February 10, 2015, 09:47:58 am

Nice cutting Tommy. Do you have any trouble cutting with a spiral blade. I just ordered some # 3 from Mike to try out. I never had to much luck with them but I have a much better scroll saw now that I had before. A Dewalt 788.

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: Keefie on February 10, 2015, 10:20:54 am

Great work there Tommy (have you tried it to see if it works?? - or won't the missus let you !!)

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: pddesertrat on February 10, 2015, 11:25:18 am

Great cutting.  I ain't gonna kiss ya!!

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: tommyb43 on February 10, 2015, 12:31:11 pm

Thanks for the comments folks that's what i like about you lot no slagging off  ;D
Keefie of course it works i am Irish  8)
Paul you are a spoilsport you should Kiss a Paddy once in a wile my wife does all the time  :P
Ralph i just got my no 3 from Mike today and they look better than Power Record that i used,
I found it OK to cut with follow the advice of my peers on here slow and steady don't stop in the middle of a line
because spirals have no mercy they cut 24/7 360deg and can mess up a line easy (Have a look at my first attempts in my gallery)

Thanks once again to one and all

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: wombatie on February 14, 2015, 05:32:05 am

You did a very neat job. You should wear it as a very large badge on St Pat's Day.   :D :D :D

Marg

Title: Re: Kiss Me I am Irish " Paddy's Day Around the corner"
Post by: Marcellarius on February 15, 2015, 09:57:47 am

nice job