Scrollsaw Workshop Community -Please register to enable posting.

General Category => Brag Forum => Topic started by: Marcellarius on May 10, 2013, 04:26:01 am

Title: vase from Steve (WIP)
Post by: Marcellarius on May 10, 2013, 04:26:01 am

made the vase from Steve's pattern.
slightly changed the pattern at the bottom. (left over from the top section...)
made from pine.
gonna finish it with polyurethane.
will start with a 10/90 BLO/mineral spirit, then a 30/30/30 BLO/MS/PU
and the inside Will get a few PU layers to make it waterproof.

Title: Re: vase from Steve (WIP)
Post by: DWSudekum on May 10, 2013, 05:09:56 am

Looks good.  Those are fun to make.  Thanks for sharing this one with us.


DW

Title: Re: vase from Steve (WIP)
Post by: Al W on May 10, 2013, 07:56:08 am

Looks nice.  Do you recall the name of the pattern?  What type of wood did you use?

Thanks for sharing.

Title: Re: vase from Steve (WIP)
Post by: frankorona on May 10, 2013, 07:59:42 am

Wonderful job, looks great, thanks for sharing

Title: Re: vase from Steve (WIP)
Post by: newfie on May 10, 2013, 09:34:03 am

nice thanks for sharing

Title: Re: vase from Steve (WIP)
Post by: Marcellarius on May 10, 2013, 11:21:49 am

Quote from: Al W on May 10, 2013, 07:56:08 am

Looks nice.  Do you recall the name of the pattern?  What type of wood did you use?

Thanks for sharing.

pattern: http://www.stevedgood.com/concentricbowl.pdf

as said, wood is pine

good luck!

Title: Re: vase from Steve (WIP)
Post by: dgman on May 10, 2013, 08:33:22 pm

Very nice looking vase Marcel! Be advised, polyurethane will not make the inside waterproof for very long. Water will eventually penetrate the poly. I would Use a two part epoxy for that.

Title: Re: vase from Steve (WIP)
Post by: Marcellarius on May 11, 2013, 02:30:59 am

Quote from: dgman on May 10, 2013, 08:33:22 pm

Very nice looking vase Marcel! Be advised, polyurethane will not make the inside waterproof for very long. Water will eventually penetrate the poly. I would Use a two part epoxy for that.

thanks Dan, went to the paint store and asked if the poly was ok for it and they said it was.....
they use the poly on wooden boats as well.
now you say this I might consider buying some.
guess my wife wont put on flowers for weeks right, just a couple of days.
let you know

Title: Re: vase from Steve (WIP)
Post by: saggioculo on May 11, 2013, 03:01:27 am

This came out very nice!  Great job.

Title: Re: vase from Steve (WIP)
Post by: Russ C on May 11, 2013, 09:05:21 am

Looks great, nick work. Thanks for sharing.  :)

Title: Re: vase from Steve (WIP)
Post by: countryscroller on May 12, 2013, 07:31:40 am

Nice job!

Title: Re: vase from Steve (WIP)
Post by: Keefie on May 12, 2013, 05:19:26 pm

great looking project.

Title: Re: vase from Steve (WIP)
Post by: wombatie on May 12, 2013, 10:11:06 pm

Looks great, well cut.

Marg