Scrollsaw Workshop Community -Please register to enable posting.

General Category => Tutorials, Techniques and Tips => Topic started by: boolat on April 13, 2013, 02:14:25 pm

Title: Proxxon 28092 DSH support for blade OLSON?
Post by: boolat on April 13, 2013, 02:14:25 pm: hello,

I have the model proxxon 28092 DSH.
I'm happy with the machine ;)
I'm disappointed for the blade holder
blades without pin slides, I have very strong tighten the screws! problem is that the screw breaks!

(https://lh3.googleusercontent.com/-zKXGZDXSUpU/UVbxa4PdvtI/AAAAAAAABi0/pxLiuIOZs1s/s646/03.JPG)

(https://lh6.googleusercontent.com/-fuTvOEG8fUY/UVgfyWJky3I/AAAAAAAABkA/z9MgTsfCphI/s646/P1350686.JPG)

I realized this:
(https://lh3.googleusercontent.com/-Z-hHEvaNX9w/UWmdggNd_1I/AAAAAAAABow/_BK3tgEpaWw/s646/Photo1344.jpg)
not very good ....

support for blade OLSON?

thank you

I want a piece like this: To easily set up the blades without pin

(http://www.shopsmith.net/forums/attachment.htm?attachmentid=17324&d=1335727988)

(http://www.rockler.com/how-to/wp-content/uploads/Proxxon-Blade-Tension-Control.jpg)

(http://www.rockler.com/how-to/wp-content/uploads/Ryobi-Blade-Change-System.jpg)

(http://www.nmatools.co.uk/uploads/Image/deco/Detail-SbHalter-eingespanntweb.jpg)

I have a chance to find?
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: LeBlack on April 14, 2013, 03:12:57 pm: :) Hi Borat :),

I've read your's, need some time to show you my photo's because of work.
The screw's are not the best but the holding for the blade is good. In German we say " Klemmhebel M4 ".

Greetz Birger
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: boolat on April 15, 2013, 05:33:06 am: Quote from: LeBlack on April 14, 2013, 03:12:57 pm
:) Hi Borat :),

I've read your's, need some time to show you my photo's because of work.
The screw's are not the best but the holding for the blade is good. In German we say " Klemmhebel M4 ".

Greetz Birger

thank you ....

I'll try to make a piece in Alumimium for only blades without pin ....
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: Tomsunnu on April 15, 2013, 07:52:22 am: Quote from: boolat on April 15, 2013, 05:33:06 am
Quote from: LeBlack on April 14, 2013, 03:12:57 pm
:) Hi Borat :),

I've read your's, need some time to show you my photo's because of work.
The screw's are not the best but the holding for the blade is good. In German we say " Klemmhebel M4 ".

Greetz Birger

thank you ....

I'll try to make a piece in Alumimium for only blades without pin ....

Hi borat, if you have a solution kindly please share with me as I have proxxon dsh and facing a similar problem with the blade holding clamps, it will be a big help :)

Thank you

Mahendra
Borat, bir ??z?m olarak sempati duyan l?tfen benimle paylaşın BEN proxxon bakacak ve dsh benzer bir sorun, bı?ak tutma kelep?eleri, b?y?k bir yardım :) teşekk?rler Mahendra
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: boolat on April 16, 2013, 10:59:37 am: my realization.
12x12mm hard metal cutting work and 6mm screws
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: Tomsunnu on April 16, 2013, 11:21:17 am: Boolat,
Thank you :) I am a bit confused, how does the bolt hold the blade ,because it is going through the holder ?please is it possible to dismantle the clamp and give me a better look ,so that I can get hold of someworkshop and get it made . This clamp issue is giving me trouble big time. Your help is really appreciated :)

Thank you
Mahendra

Boolat, Teşekk?r Ederiz :) I am a bit karışmış, tutun, cıvata, blade ,??nk? ge?erek tutucu ?l?tfen m?mk?nd?r, kilit ve s?k?n beni bir daha iyi g?r?n?m ,ki someworkshop elde ve yapılır . Bu kilit sorun, bana sorun veren b?y?k an. Yardım ger?ekten takdir ediyorum :) teşekk?rler Mahendra
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: boolat on April 16, 2013, 11:41:34 am: ok ne problem ;D
use plywood http://www.stevedgood.com/ex21knob.pdf

to the left is I use loctide so that it does not move
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: Tomsunnu on April 16, 2013, 10:09:37 pm: Boolat,

thank you so very much :) I will take this drawing to the work shop and see if the understand, if not I will trouble you again- I hope it is not a problem? :)

The knob by Steve I made that long back but the clamp was a problem.

Mahendra
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: LeBlack on April 18, 2013, 02:55:17 pm: :) Hi Boolat and Mahendra,

sorry, I had a lot of work....so here is my solution. I changed the screw quality from 5.9 to 8.8. The small metal sheets have to be turn when using blades without pins (arrow) Pic. 2. For the upper clamp I use a normal clamping lever with threat M4. So you can pull together the clamp a little stronger. The working now is very good.
I'm using Nequa Ultra blades (the same as knewn as The Flying Dutchman in other countries).

Greetz Birger :)
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: Tomsunnu on April 18, 2013, 10:35:44 pm: Birger, thank you for your trouble. My problem is the clamp it self has lost the gripping power,plus twice I have resized the entry holes :-[, what I need is the solution given by Boolat, as i need totally new set of clamps,up and down. Hopefully the workshop people should help me out,I have taken the copies of the drawing plus the photo of his clamp,and I am sure that it should be solved :)

Thank you once again

Mahendra
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: mirec437 on January 27, 2015, 02:26:31 am: I am sure the problem.
Title: Re: Proxxon 28092 DSH support for blade OLSON?
Post by: Ben on January 27, 2015, 04:27:47 am: I have the same little clamps as shown in one of the first few pictures. for me they are to fiddly to do up tight and are very hard to place on the bottom clamp through the insert hole in the table.
I like the looks of that new design but im still not sure on a setup I could use on my saw