Scrollsaw Workshop Community -Please register to enable posting.

General Category => Introduce Yourself. => Topic started by: 3billy3 on October 10, 2012, 03:25:38 pm

Title: Hi from Somerset - UK
Post by: 3billy3 on October 10, 2012, 03:25:38 pm

Hi All

Wow! great community, loads of ideas and good work.

I'm fairly new to the hobby, biggest problem for me is what to make next! That and my eternal struggle with a poor quality machine, but you have to start somewhere and I'm saving hard for a scroll saw upgrade!

Keep the community going it's very inspirational to all.

Neil

Title: Re: Hi from Somerset - UK
Post by: Billy in Va on October 10, 2012, 03:58:41 pm

Hi Neil, Welcome to the group. I understand the upgrade dilemma -  its an ongoing thing for me.

Title: Re: Hi from Somerset - UK
Post by: countryscroller on October 10, 2012, 04:41:28 pm

Hi Neil, welcome to the forum. I'm Dustin aka Country Scroller from Ohio. I hope you get the upgrade, it pays off trust me. I started on a crappy saw that was ages old past down from my grandpa.

Title: Re: Hi from Somerset - UK
Post by: dgman on October 10, 2012, 05:44:59 pm

Hey Neil, Welcome to the forum! I'm Dan from Southern California. Come on in and join the fun!

Title: Re: Hi from Somerset - UK
Post by: Stravides on October 10, 2012, 06:13:38 pm

Hi there Neil - Ken from South Wales - Uk here, dont worry I been doing this for only 3 months now and also have a level entry machine - what I can say tho is make sure you use some nice quality blades and you should be fine ;)

Title: Re: Hi from Somerset - UK
Post by: Keefie on October 10, 2012, 06:36:08 pm

Hi neil, welcome to the forum, I'm Keith from Cornwall. Just down the road from you. I too started out with an entry level machine (A Clarke 16") was about a basic a machine as you can get. But you can still turn out some good stuff on a basic machine it just takes a little longer with blade changing. But one piece of advice - good blades make all the difference, the best I have found so far are the Flying Dutchman Ultra Reverse blades, every third tooth is reversed and gives such a clean cut there is almost no sanding needed. Check them out at http://www.mikesworkshop.com/blades.htm
Hope this helps, and the kettle is always hot if you ever get down Newquay way. (offer is open to anyone coming to Newquay)

Title: Re: Hi from Somerset - UK
Post by: bzeyher on October 10, 2012, 06:43:41 pm

Hello Neil, welcome to the forum. My wife comes from Martock in Somerset and I have been there many times. Have fun with the hobby.

Title: Re: Hi from Somerset - UK
Post by: Keefie on October 10, 2012, 06:47:00 pm

I was in Martock a few weeks ago for their woodturning show at Yandles.

Title: Re: Hi from Somerset - UK
Post by: bzeyher on October 10, 2012, 08:40:14 pm

Been to their cafe a few times, but always missed the shows.

Title: Re: Hi from Somerset - UK
Post by: Russ C on October 10, 2012, 09:26:06 pm

Welcome to the Scrollsaw Forum Neil. I'm Russ from Florida. Take your shoes off and jump in and get your feet wet.  :)

Title: Re: Hi from Somerset - UK
Post by: wombatie on October 11, 2012, 01:51:29 am

Hi Neil, welcome to the forum. I'm Marg from Australia.

Marg

Title: Re: Hi from Somerset - UK
Post by: Keefie on October 11, 2012, 08:14:05 am

Russ, If he gets his feet wet, does that mean his workshop's leaking? ::)

Title: Re: Hi from Somerset - UK
Post by: rob roy on October 11, 2012, 11:30:13 am

Hi Neil, I'm Roy from Scotland, welcome to the forum, Come on in and kick up some sawdust. I've been using a crappy saw for some time now, but a bit of perseverance and more importantly, as Keefie says, GOOD BLADES!!!!!!. Good luck.
Rob Roy.

Title: Re: Hi from Somerset - UK
Post by: 3billy3 on October 12, 2012, 04:57:29 pm

Thanks for the warm welcome everyone!

Title: Re: Hi from Somerset - UK
Post by: newfie on October 12, 2012, 06:43:43 pm

welcome Neil i'm Todd from NL Canada

Title: Re: Hi from Somerset - UK
Post by: julief on October 13, 2012, 07:03:21 am

Hi Neil and welcome to the forum.  I'm Julie from Texas.  Glad to have you.

Title: Re: Hi from Somerset - UK
Post by: Al W on October 13, 2012, 08:28:08 am

Greetings from South Dakota, USA.  Welcome to the group.

Title: Re: Hi from Somerset - UK
Post by: Judy Hunter on October 13, 2012, 10:56:35 am

Hello Neil, I'm Judy from North Dakota, USA. Welcome and have fun making saw dust.