1
General Scroll Saw Talk / Charles Dearing
« on: January 02, 2019, 03:38:14 pm »
I was just on scroll saw cafe and read that Charles Dearing had a very bad house fire. There is a link for donations if anyone is interested
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Scroll Saw Talk / Where is everyone
« on: August 14, 2018, 04:52:25 pm »
Where is everyone
3
General Scroll Saw Talk / Strange dewalt happening
« on: June 18, 2018, 08:18:04 pm »
My dw788 is about 3 months old i had to tighten my lamp and realized the bottom bolt is stripped so i tightened the top extra tight an now my head stays up without my piece of wood i loosened the lamp bolt and it still does it i have been using the saw but am wondering if there is a problem when i lft it it locks into place and there is very little resistance to put it back down right now it works like the delta.
4
General Scroll Saw Talk / Fret work clean up
« on: May 31, 2018, 09:25:27 pm »
Not sure how many scrollers do this, but i keep a dull 2/0 blade and use it by hand to clean all my fret work fuzzies. I find it faster then using blade sanders and small pieces of sand paper. I also use the end of a 5 blade to clean glue sqeeze out
5
Pattern Requests. / Step aside coffee
« on: May 03, 2018, 06:19:31 am »
I made the step aside coffee this is a job for alcohol pattern for my neighbor. My wife saw it and asked if there was one with a wine bottle.
6
General Scroll Saw Talk / Better bulb for dewalt
« on: April 29, 2018, 01:30:50 pm »
I live very close to Toronto and was wondering if anyone has found an led bulb that works in the dw88 factory light. Thanks and happy scrolling.
7
General Scroll Saw Talk / Dewalt dw788 tilt issue
« on: April 15, 2018, 12:53:02 pm »
I'm having an issue tilting my table. I almost have to remove the tightening knob to tilt it. Even then i have to wiggle it to get it to move. Any tricks would be much appreciated, thanks
8
General Scroll Saw Talk / New saw
« on: April 13, 2018, 08:03:44 pm »
Just upgraded my saw from porter cable to Dewalt DW 788 and I love it
9
Ask Steve a question. / 162 IQ
« on: April 09, 2018, 07:51:54 am »
Is Kellie really a 162 iq. Would that be like, chip off the old block. Lol
10
Pattern Requests. / Cricket player
« on: March 10, 2018, 09:56:04 pm »
Im looking for a cricket player pattern.if anyone could help me it would be much appreciated.
11
General Scroll Saw Talk / Cricket player
« on: March 09, 2018, 02:37:44 pm »
I was wondering if anyone knows where i can find a pattern of a cricket player. I would like to do one for my fathr in law.
12
General Scroll Saw Talk / Oops
« on: March 09, 2018, 01:55:08 am »
I had just finished cutting steves ship in a bottle from 1 inch hardwood. In the process of gluing it to to backing board, i dropped it and broke it in 5 pieces. Three hours and 4 blades that i will never get back.
13
General Scroll Saw Talk / Foot pedal
« on: February 14, 2018, 09:19:28 pm »
I have a porter cable saw and was wondering if anyone has tried a foot pedal. I'm Leary about buying one due to the slow start motor
Pages: [1]
