31
General Scroll Saw Talk / Re: knobs
« on: February 16, 2015, 08:08:37 pm »
Lowe's & home Depot have a few small wooden knobs.
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
32
General Scroll Saw Talk / Re: How long to wait for a order?
« on: February 13, 2015, 06:28:45 am »
Who is "her", we all probably would like to know, at least I do so I don't make a mistake of ordering from "her".
33
General Scroll Saw Talk / Re: My recycled saw
« on: January 19, 2015, 06:14:34 pm »
Looks good to me. 
34
The Coffee Shop / Re: Anyone need this info ??
« on: January 19, 2015, 12:51:59 pm »
And I thought I was the only one that did that, along with forgetting to start the dust collector sometimes.
A word of advice the dust collector works a lot better when running than not.
A word of advice the dust collector works a lot better when running than not.
35
General Scroll Saw Talk / Re: Russ has videos
« on: January 15, 2015, 08:23:38 pm »
Did he send out notices that it was on line. I subscribed but never got a notice of the video. I watched this one because I saw Judy's post that it was there, and the site shows me as subscribed?
?
?
36
The Coffee Shop / Re: New Video *Simply Wooden Creations*
« on: January 09, 2015, 08:41:55 am »
Subscribed yesterday, waiting for the 1st video!
37
Tutorials, Techniques and Tips / Re: Brass gauge setup blocks?
« on: January 08, 2015, 12:46:11 pm »
My luck, MLCS called this morning and said the brass set I ordered has been discontinued. So I ordered the Veritas set of 2" long starting at 1/16", guess they will have to do.
38
Tutorials, Techniques and Tips / Brass gauge setup blocks?
« on: January 07, 2015, 06:16:28 pm »
Does not really apply to scroll sawing but does anyone know where I could find a set of brass gauge setup blocks that start at 1/16" & up, all the ones I find start at 1/8" and up. If I could find a 1/16" I could add it to the sets I found. Anyone know where I can find such a animal?
39
The Coffee Shop / Re: My Wonderful Collection :)
« on: December 31, 2014, 07:47:53 pm »
Looks like you have some good friends!
40
General Scroll Saw Talk / Re: Font Idenity
« on: December 28, 2014, 05:00:59 pm »
Close enough for now, thanks for all the responses.
42
General Scroll Saw Talk / Font Idenity
« on: December 27, 2014, 09:40:08 pm »
I cannot remember nor find the name of this font.
Any help appreciated.
TIA bob
Any help appreciated.
TIA bob
43
General Scroll Saw Talk / Re: spraying clear finish
« on: December 24, 2014, 07:57:51 am »
I love Minwax aerosol products as it has a the absolute best spray head I have ever seen on a rattle can. That is all I use now on my outdoor projects, Minwax Helmsman exterior Polyurethane. I get it at Wallyworld.
44
General Scroll Saw Talk / Re: sanding down draft table
« on: December 21, 2014, 05:43:13 pm »
I could possibly get by with 12 x 30, 12 x 24 is a little too short for my uses as I like to make signs that are very often 23 to 27 inches long. Either way I will definitely put a couple of cross braces with large holes in them under the pegboard for extra support.
45
General Scroll Saw Talk / Re: sanding down draft table
« on: December 21, 2014, 02:45:35 pm »
1/4" peg board 12" x 36" would have enough holes for 4" hose. I am thinking about 1 or 2 cross braces under the peg board with a couple of 2" holes or larger through each cross brace would give me 21.19 sq inches through the 1/4" peg board, 4" has a area of 12.56 sq inches. I cannot think of anything else to use for the top except. 1/8" peg board 12" x 36" would have 5.3 sq inches which would be good for a 2.5" line or a shop vac.
1/8" peg board 12" x 36" would have 5.3 sq inches which would be good for a 2.5" line or a shop vac.
