« previous next »
Pages: [1]   Go Down

Author Topic: 3D  (Read 2864 times)

Offline gordster

  • ****
  • Sr. Member
  • Posts: 345
  • Nova Scotia, Canada
    • View Profile
3D
« on: September 04, 2014, 11:11:35 pm »
One of Steves 3d ornaments
Logged
Gordie

Offline wildhorse

  • **
  • Jr. Member
  • Posts: 64
    • View Profile
Re: 3D
« Reply #1 on: September 05, 2014, 01:53:11 am »
Nicely done.
Logged

Offline spirithorse

  • *****
  • Hero Member
  • Posts: 923
    • View Profile
Re: 3D
« Reply #2 on: September 05, 2014, 02:27:19 am »
Nice work!
Thank you for sharing and God Bless! Spirithorse
Logged

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: 3D
« Reply #3 on: September 05, 2014, 04:56:37 am »
Very nice.

Marg
Logged
MARG

No one notices what I do until I'm not here to do it............

Offline DWSudekum

  • *****
  • Hero Member
  • Posts: 3677
    • View Profile
    • The DW Collection
Re: 3D
« Reply #4 on: September 05, 2014, 06:11:50 am »
Very nicely done.  Thanks for sharing this with us.

DW
Logged
Life is tough, it is even tougher if you are stupid  -  John Wayne

Offline pierre62

  • *****
  • Hero Member
  • Posts: 687
    • View Profile
Re: 3D
« Reply #5 on: September 05, 2014, 06:37:32 am »
Very nice !
Logged
Pierre

Offline frankorona

  • *****
  • Hero Member
  • Posts: 4030
  • Frankorona (Frank) (Crown)
    • View Profile
    • Frankorona?s workshop
Re: 3D
« Reply #6 on: September 05, 2014, 08:15:21 am »
Wonderful ornament, thanks for sharing.
Logged

pddesertrat

  • Guest
Re: 3D
« Reply #7 on: September 05, 2014, 10:20:09 am »
Nice!
Logged

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: 3D
« Reply #8 on: September 05, 2014, 10:32:16 am »
That's a nice looking piece. What wood did you use for the compound cut?
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline gordster

  • ****
  • Sr. Member
  • Posts: 345
  • Nova Scotia, Canada
    • View Profile
Re: 3D
« Reply #9 on: September 05, 2014, 03:46:07 pm »
I used a piece of basswood I  have.The 1st one came out good, but second one I broke.Since then I have read a tip .not go complete full cut as to keep pieces together for strength.then cut off lsst holding spots.then wiggle it apart, dust stays in to make it more fun lol.
Logged
Gordie

Offline newfie

  • *****
  • Hero Member
  • Posts: 5037
  • The Way I Scroll
    • View Profile
    • some of my woodworking
Re: 3D
« Reply #10 on: September 12, 2014, 09:37:17 pm »
great work thanks for sharing
Logged


excalibur 21
Every woodworker needs a fireplace

Offline Marcellarius

  • *****
  • Hero Member
  • Posts: 6135
  • Scrolling each day, keeps the doctor away
    • View Profile
    • Some of my work
Re: 3D
« Reply #11 on: September 13, 2014, 06:22:23 am »
very nice cutting. looks great
Logged
Marcel

sometimes I make designer firewood....

countryscroller

  • Guest
Re: 3D
« Reply #12 on: September 17, 2014, 07:40:55 am »
Great work! Thanks for sharing.
Logged

Bullfighter

  • Guest
Re: 3D
« Reply #13 on: September 22, 2014, 03:04:57 am »
So beautiful, nice job. My wife loved it.
Logged

Rover2

  • Guest
Re: 3D
« Reply #14 on: September 22, 2014, 09:15:30 pm »
I was playing around one day and made that ornament out of the only thing I had on hand at the time which was Pine and managed to break it only seconds after cutting.  Next time I will use a better wood.
Yours came out great.  VERY nice work and thanks for sharing with us.
Al
Logged
Pages: [1]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj